contact us
HK LEE HING INDUSTRY CO., LIMITED
products
- Main Products
technical articles
Company News
- Pollution Degree and How It Changes the Creepage Requirement2026-11-15
- 0.2 J or 1 J? Matching the Spring Hammer to the Standard2026-11-14
- Measuring Creepage and Clearance Under IEC 61010-12026-11-13
- Class II Dielectric Strength: 3,000 V and the Y-Capacitor Path2026-11-17
- Earth Continuity: 25 A or 40 A, 0.1 Ω and the Two-Second Option2026-11-17
- Dielectric Test Frequency: Why 50 Hz and 1 kHz Are Not the Same Test2026-11-17
- Impulse Voltage Testing: The 1.2 by 50 Microsecond Waveform2026-11-16
- Thermocouple Attachment for Temperature Rise: The Cement Trap2026-11-16
- What IEC 61010-1 Covers and What It Leaves to the Part 2 Standards2026-03-03
- Pollution Degree 1, 2 and 3: The Number Behind Every Clearance2026-03-06
- Overvoltage Category I to IV: Where the Instrument Sits in the Supply Chain2026-03-10
- Walking the Clearance Table Without Getting Lost2026-03-13
- Creepage Distance and CTI: When the Material Decides the Gap2026-03-17
- The Dielectric Strength Test: Setup Details That Decide the Result2026-03-20
- Why the AC Test Lasts One Minute, and When DC Is Allowed2026-03-24
- Protective Bonding: The 0.1 Ohm Test and What It Really Checks2026-03-27
- Touch Current: Which Limit Applies and Why the Network Matters2026-03-31
- Class I and Class II: Two Ways to Be Safe, Two Different Test Sets2026-04-02
- Enclosure Requirements in IEC 61010: More Than an IP Number2026-04-07
- Temperature Rise: Limits, Ambient Assumptions and the Parts People Forget2026-04-10
- Batteries in IEC 61010: Charging, Venting and the Reverse Polarity Case2026-04-14
- Flammability of Enclosures: Why the Material Grade Is a Safety Claim2026-04-17
- Mechanical Hazards: Drop, Tip and the Stability of a Bench Instrument2026-04-21
- Rating Plate Markings: The Smallest Page of the Safety File2026-04-24
- Measurement Category Symbols: What CAT II and CAT III Really Promise2026-04-28
- Instruction Manual Requirements: The Clauses Test Houses Read First2026-05-04
- A Certified Component Does Not Make a Certified Instrument2026-05-07
- Routine Tests and Type Tests: Two Different Promises2026-05-11
- Fuses and Protective Devices: Rating, Breaking Capacity and the Wrong Replacement2026-05-14
- High Voltage Inside an Instrument: Insulation, Interlocks and Discharge2026-05-18
- Capacitor Discharge: The Hazard That Remains After Unplugging2026-05-21
- Altitude Correction: Why Clearances Grow Above 2000 m2026-05-25
- Humidity Preconditioning: The Step That Decides the Dielectric Result2026-05-28
- IEC 61010 and IEC 62368-1: Which Standard Applies to Your Bench Instrument2026-06-01
- The Ten Findings That Repeat in IEC 61010 Testing2026-06-04
- Preparing a Sample for IEC 61010 Testing2026-06-08
- Reading and Documenting an IEC 61010 Test Report2026-06-11
- Choosing a Bench Multimeter by Safety Rating, Not by Digits2026-06-15





